Methodology to evaluate design modifications intended to eliminate frosting and high discharge temperatures in air-source heat pumps (ASHPs) in cold climates
Date
2024-06-01
Authors
Gollamudi, Siddhartha
Krishnan, Easwaran N
Fauchoux, Melanie
Ramin, Hadi
Joseph, Albin
Simonson, Carey
Journal Title
Journal ISSN
Volume Title
Publisher
Elsevier
ORCID
Type
Article
Degree Level
Abstract
Air-source heat pumps (ASHPs) operating in cold climates experience problems with frosting and high refrigerant temperatures. These problems increase energy consumption, and their severity depends on the climatic conditions. In the present paper, a methodology for identifying the prevailing problem between frosting and high discharge temperatures is presented. Three performance indices, the frosting index (FI), the discharge index (DI), and the total loss index (TLI), are proposed to quantify the impacts of frosting and high discharge temperatures on the annual performance of ASHPs in different climatic conditions. The FI and DI show which problem (frosting or high discharge temperature) dominates, and the TLI indicates the combined effect of frosting and high discharge temperatures on the performance of an ASHP. A thermodynamic model of an ASHP coupled with the TRNSYS building simulation tool is used to estimate the performance of an ASHP and the proposed loss indices to estimate the impact of both frosting and high discharge temperatures for 45 cities in Canada. The results can be extended to other parts of the world that experience similar climatic conditions The results reveal that in cities in ASHRAE climatic zones 5 and 6 (classified as cold regions) where the ambient air temperatures are predominantly between −15 °C to 6 °C, ASHPs are heavily impacted by frosting. The problem of high discharge temperatures in ASHPs is predominant in cities in climate zones 7 and 8 (classified as very cold and subarctic regions) where the temperatures are frequently below −20 °C in winter. Among the cities considered, St. John, NL has the highest fraction of heating hours experiencing frosting (90 %), where the annual increase in energy consumption due to frosting is 13.5 % of the annual heating energy consumption. The highest annual increase in energy consumption due to high discharge temperatures is in Isachsen, NU (zone 8), where the increase is 30 % of the annual heating energy consumption.
Based on the proposed indices, another index called the performance gain index (PGI) is created, which can be used as a first step to assess the energy-saving potential of design modifications applied to ASHPs to solve the problems of frosting and high discharge temperatures. The PGI will aid in developing climate specific ASHPs. One possible design modificationis the use of a two-stage ASHP with an economizer. It is observed that the two-stage ASHP with economizer can mitigate high discharge temperatures and improve performance in very cold and subarctic regions (zones 7 and 8). However, it is not as beneficial in zones 5 and 6, where the impact of high discharge temperatures on performance is minimal and frosting dominates. Finally, a case study, using the PGI to evaluate the economic and environmental effectiveness of a two-stage ASHP with economizer is presented for the city of Saskatoon.
Description
This is an Accepted Manuscript of an article published by Elsevier in Energy and Building on 01 June 2024, available at: https://doi.org/10.1016/j.enbuild.2024.114209
Keywords
Air-source heat pumps, Frosting, High refrigerant discharge temperature, Climate specific air-source heat pump, Two-stage air-source heat pump
Citation
Siddhartha Gollamudi, Melanie Fauchoux, Easwaran Krishnan, Hadi Ramin, Albin Joseph, Carey Simonson. (2024). Methodology to evaluate design modifications intended to eliminate frosting and high discharge temperatures in air-source heat pumps (ASHPs) in cold climates, Energy and Buildings, 312, 114209. https://doi.org/10.1016/j.enbuild.2024.114209.
Degree
Department
Program
Advisor
Committee
Part Of
item.page.relation.ispartofseries
DOI
https://doi.org/10.1016/j.enbuild.2024.114209